Datamax-oneil DPL Programmer’s Manual Manual do Utilizador Página 3
- Página / 296
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
i
Contents
1 Overview ...................................................................................... 1
Who Should Use this Manual ...................................................................... 1
The Scope of this Manual ........................................................................... 1
General Conventions ................................................................................. 2
Computer Entry and Display Conventions .................................................... 2
Important Safety Instructions .................................................................... 2
Special Instructions .................................................................................. 2
Typical Data Flow Sequence ....................................................................... 3
2 Control Code Command Functions ................................................ 7
Introduction ............................................................................................ 7
Attention-Getters ..................................................................................... 7
Easy Control Codes .................................................................................. 7
Alternate Control Code Modes .................................................................... 8
3 Immediate Command Functions ................................................... 9
Introduction ............................................................................................ 9
SOH # Reset ...................................................................................... 9
SOH * Reset ...................................................................................... 9
SOH A Send ASCII Status String ......................................................... 10
SOH a Send ASCII Extended Status String ........................................... 10
SOH B Toggle Pause ......................................................................... 11
SOH C Stop/Cancel ........................................................................... 12
SOH D SOH Shutdown ....................................................................... 12
SOH E Send Batch Remaining Quantity ................................................ 12
SOH e Send Batch Printed Quantity .................................................... 13
SOH F Send Status Byte .................................................................... 13
4 System-Level Command Functions ............................................. 15
Introduction .......................................................................................... 15
STX A Set Time and Date .................................................................. 15
STX a Enable Feedback Characters ..................................................... 16
STX B Get Printer Time and Date Information ...................................... 16
STX c Set Continuous Paper Length ................................................... 17
- Programmer’s Manual 1
- Contents 3
- 1 Overview 9
- General Conventions 10
- Special Instructions 10
- Typical Data Flow Sequence 11
- ) commands can be changed at 13
- Overview 14
- 15
- Alternate Control Code Modes 16
- Immediate Command Functions 17
- SOH B Toggle Pause 19
- SOH C Stop/Cancel 20
- SOH D SOH Shutdown 20
- SOH F Send Status Byte 21
- STX A Set Time and Date 23
- STX I Input Image Data 27
- STX o Cycle Cutter 30
- STX P Set Hex Dump Mode 31
- STX p Controlled Pause 31
- STX Q Clear All Modules 31
- STX q Clear Module 32
- STX R Ribbon Saver Control 32
- STX S Set Feed Speed 33
- STX T Print Quality Label 33
- STX X Set Default Module 37
- STX z Pack Module 40
- Extended System-Level 41
- STX Kb Backfeed Time Delay 44
- STX KC Get Configuration 45
- STX Kc Configuration Set 48
- STX KE Character Encoding 101
- STX KH Dot Check 104
- STX KI GPIO Input 106
- STX Kn NIC Reset 106
- STX KO GPIO Output 107
- STX Kp Module Protection 108
- Label Formatting 119
- Command Functions 119
- A Set Format Attribute 120
- B Bar Code Magnification 121
- C Set Column Offset Amount 121
- H Enter Heat Setting 124
- J Justification 125
- M Select Mirror Mode 125
- P Set Print Speed 126
- of .37 128
- S Set Feed Speed 130
- Embedding 135
- STX D Print adjusted date 137
- STX T Print Time and Date 138
- Introduction 141
- )s###W Font Descriptor 142
- *c###E Character Code 142
- 8 Generating Label Formats 143
- Generating Records 144
- The Structure of a Record 144
- Record Structure Types 148
- Fill Patterns 155
- Generating Label Formats 158
- Appendix A 161
- 10K OHM 1/4 WATT 163
- Appendix B – Sample Programs 164
- Appendix C 173
- Appendix C – Available Fonts 176
- Appendix D 179
- Appendix D – Reset Codes 180
- Appendix E 181
- Appendix E – Symbol Sets 192
- Appendix F 193
- Appendix G 199
- Barcode I 204
- Barcode S 208
- Barcode T 208
- Barcode U 211
- Barcode z 212
- Barcode Z 213
- Barcode W1c 215
- Barcode W1C 216
- Barcode W1D 220
- Barcode W1f 225
- Barcode W1F 225
- Barcode W1G 226
- Barcode W1I 228
- Barcode W1J 229
- Barcode W1k 231
- Barcode W1L 233
- Barcode W1M 235
- Barcode W1m 235
- Barcode W1N 235
- (IMB) 236
- 34 567890 123 4567 238
- Barcode W1t 239
- Barcode W1Y 240
- Barcode W1Z 242
- Appendix H 245
- Appendix I 247
- Appendix J 251
- • Pins 1 – 2 = +5VDC; 252
- • Pins 2 – 3 = +24VDC; or 252
- • None = A common external 252
- Appendix K 253
- Appendix L 255
- Appendix M 257
- Appendix N 259
- Appendix N – Image Loading 260
- Appendix O 261
- Appendix P 263
- Appendix Q 273
- Appendix R 275
- Appendix R – Line Mode 276
- Appendix S 279
- Appendix S – RFID Overview 280
- Field Valid Inputs Meaning 283
- Appendix T 285
- Appendix U 291
- Glossary 293
Manuais e produtos relacionados com Impressoras Datamax-oneil DPL Programmer’s Manual
(8 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.028 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais