Datamax-oneil DPL Programmer’s Manual Manual do Utilizador Página 201
- Página / 296
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Appendix G – Bar Code Details
193
This printer supports the Code 128 subsets A, B, and C. The printer can be selected to
start on any code subset and switch to another within the data stream. The default code
subset is B; otherwise, the first character (A, B, C) of the data field determines the
subset. Subset switching is only performed in response to code switch command. These
commands are placed in the data to be encoded at appropriate locations.
The use a B as the first character is recommended to prevent an A or C from changing
the subset.
Subset A: Includes all of the standard uppercase alphanumeric keyboard characters
plus the control and special characters. To select Code 128 Subset A, place an ASCII A
(DEC 65, HEX 41) before the data to be encoded.
Subset B: Includes all of the standard uppercase alphanumeric keyboard characters
plus the lowercase alphabetic and special characters. To select Code 128 Subset B, place
an ASCII B (DEC 66, HEX 42) before the data to be encoded. If no start character is sent
for the Code 128 font, Code 128 Subset B will be selected by default.
Subset C: Includes the set of 100 digit pairs from 00 through 99 inclusive, as well as
special characters. Code 128 Subset C is used for double density encoding of numeric
data. To select Code 128 Subset C, place an ASCII C (DEC 67, HEX 43) before the data
to be encoded. Subset C can only encode an even number of numeric characters. When
the data to be encoded includes an odd number of numeric characters, the last character
causes the printer to automatically generate a “switch to subset B” and encode the last
character appropriately in subset B.
Special Character Handling: Characters with an ASCII value greater than 95 are
considered special characters. To access these values, a two-character reference table is
built into the printer (see below).
For example, to encode FNC2 into a Code 128 Subset A bar code, send the ASCII “&”
(DEC 38, HEX 26) followed by the ASCII “B” (DEC 66, HEX 41).
Sample: ATEST&B123 Encoded: TEST<FNC2>123
ASCII 2 CHAR CODE A CODE B CODE C
96 &A FNC3 FNC3 -NA-
97 &B FNC2 FNC2 -NA-
98 &C SHIFT SHIFT -NA-
99 &D CODEC CODEC -NA-
100 &E CODEB FNC4 CODEB
101 &F FNC4 CODEA CODEA
102 &G FNC1 FNC1 FNC1
- Programmer’s Manual 1
- Contents 3
- 1 Overview 9
- General Conventions 10
- Special Instructions 10
- Typical Data Flow Sequence 11
- ) commands can be changed at 13
- Overview 14
- 15
- Alternate Control Code Modes 16
- Immediate Command Functions 17
- SOH B Toggle Pause 19
- SOH C Stop/Cancel 20
- SOH D SOH Shutdown 20
- SOH F Send Status Byte 21
- STX A Set Time and Date 23
- STX I Input Image Data 27
- STX o Cycle Cutter 30
- STX P Set Hex Dump Mode 31
- STX p Controlled Pause 31
- STX Q Clear All Modules 31
- STX q Clear Module 32
- STX R Ribbon Saver Control 32
- STX S Set Feed Speed 33
- STX T Print Quality Label 33
- STX X Set Default Module 37
- STX z Pack Module 40
- Extended System-Level 41
- STX Kb Backfeed Time Delay 44
- STX KC Get Configuration 45
- STX Kc Configuration Set 48
- STX KE Character Encoding 101
- STX KH Dot Check 104
- STX KI GPIO Input 106
- STX Kn NIC Reset 106
- STX KO GPIO Output 107
- STX Kp Module Protection 108
- Label Formatting 119
- Command Functions 119
- A Set Format Attribute 120
- B Bar Code Magnification 121
- C Set Column Offset Amount 121
- H Enter Heat Setting 124
- J Justification 125
- M Select Mirror Mode 125
- P Set Print Speed 126
- of .37 128
- S Set Feed Speed 130
- Embedding 135
- STX D Print adjusted date 137
- STX T Print Time and Date 138
- Introduction 141
- )s###W Font Descriptor 142
- *c###E Character Code 142
- 8 Generating Label Formats 143
- Generating Records 144
- The Structure of a Record 144
- Record Structure Types 148
- Fill Patterns 155
- Generating Label Formats 158
- Appendix A 161
- 10K OHM 1/4 WATT 163
- Appendix B – Sample Programs 164
- Appendix C 173
- Appendix C – Available Fonts 176
- Appendix D 179
- Appendix D – Reset Codes 180
- Appendix E 181
- Appendix E – Symbol Sets 192
- Appendix F 193
- Appendix G 199
- Barcode I 204
- Barcode S 208
- Barcode T 208
- Barcode U 211
- Barcode z 212
- Barcode Z 213
- Barcode W1c 215
- Barcode W1C 216
- Barcode W1D 220
- Barcode W1f 225
- Barcode W1F 225
- Barcode W1G 226
- Barcode W1I 228
- Barcode W1J 229
- Barcode W1k 231
- Barcode W1L 233
- Barcode W1M 235
- Barcode W1m 235
- Barcode W1N 235
- (IMB) 236
- 34 567890 123 4567 238
- Barcode W1t 239
- Barcode W1Y 240
- Barcode W1Z 242
- Appendix H 245
- Appendix I 247
- Appendix J 251
- • Pins 1 – 2 = +5VDC; 252
- • Pins 2 – 3 = +24VDC; or 252
- • None = A common external 252
- Appendix K 253
- Appendix L 255
- Appendix M 257
- Appendix N 259
- Appendix N – Image Loading 260
- Appendix O 261
- Appendix P 263
- Appendix Q 273
- Appendix R 275
- Appendix R – Line Mode 276
- Appendix S 279
- Appendix S – RFID Overview 280
- Field Valid Inputs Meaning 283
- Appendix T 285
- Appendix U 291
- Glossary 293
Manuais e produtos relacionados com Impressoras Datamax-oneil DPL Programmer’s Manual
(8 páginas)Samsung UN55D6000SF manuali
Manuali dei proprietari e guide per l'utente per Lettori DVD Samsung UN55D6000SF.
We fornisce manuali pdf Samsung UN55D6000SF per scaricare gratuitamente in base al tipo di documento:
Comentários a estes Manuais