Datamax-oneil Class Series Programmer’s Manual Manual do Utilizador Página 129
- Página / 300
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Label Formatting Command Functions
Class Series Programmer’s Manual 115
H Enter Heat Setting
This command changes the “on time” of elements of the print head. The default setting is 10 (except
in the case of printers with a menu, where the default setting can be changed through the keypad). An
increase or decrease in this value results in a change of heat applied by the print head to the media,
lightening or darkening the print contrast accordingly. This is helpful when using different media
types, each requiring a different amount of heat to properly image the media. The host device can
send this command value to correct the heat setting per the application.
Syntax:
Hnn
Where:
nn
- Is a two-digit heat value (00-30)
Sample:
<STX>L<CR>
H15<CR>
141100001000100SAMPLE LABEL<CR>
E
The sample sets the printer for a heat value of 15 and prints one label.
Note: Non-Display Models – the “Darkness Potentiometer,” while providing subtle changes, is intended to
be used to match print contrast levels following print head replacements.
J Justification
This command changes the printing justification.
Note: Display-Equipped Models – This command is only valid for use with scalable fonts.
Syntax:
Ja
Where:
a
- Is a single-digit alpha character:
L = left justified (default)
R = right justified
C = center justified
Sample:
<STX>L<CR>
1911A1801001000TEST1
JR
1911A1801000100TEST2
JC
1911A1802000200TEST3
E
The sample’s first text field “TEST1” will be printed at one inch up, one inch over going right. The
second text “TEST2” will be printed at one inch up one inch over, going left. (Note the characters
will not be reversed.) The third field “TEST3” will be centered on the point two inches up two inches
over.
- Class Series 1
- Contents 5
- Overview 15
- Typical Data Flow Sequence 18
- Attention-Getters 21
- Control Commands 22
- Immediate Command Functions 23
- Immediate Command Functions 24
- SOH B Toggle Pause 25
- SOH C Stop/Cancel 26
- SOH D SOH Shutdown 26
- SOH F Send Status Byte 27
- STX A Set Time and Date 29
- STX e Select Edge Sensor 32
- STX F Form Feed 32
- STX I Input Image Data 34
- STX k Test RS-232 Port 36
- STX o Cycle Cutter 38
- STX P Set Hex Dump Mode 38
- STX p Controlled Pause 38
- STX Q Clear All Modules 38
- STX q Clear Module 39
- STX R Ribbon Saver On/Off 39
- STX S Set Feed Speed 40
- STX T Print Quality Label 41
- STX X Set Default Module 46
- STX z Pack Module 49
- STX Kb Backfeed Time Delay 54
- STX KC Get Configuration 55
- STX Kc Configuration Set 56
- Table 5-5: Network Setup 87
- Example: 95
- Table 5-13 WiFi Setup 102
- Example 1: 102
- Table 5-14 WiFi Security 103
- (Non-Display Models only) 104
- (MCL Command) 108
- STX Kp Module Protection 110
- Introduction 123
- : Set Cut By Amount 123
- A Set Format Attribute 124
- B Bar Code Magnification 125
- C Set Column Offset Amount 125
- F Advanced Format Attributes 127
- H Enter Heat Setting 129
- J Justification 129
- M Select Mirror Mode 130
- P Set Print Speed 131
- R Set Row Offset Amount 132
- S Set Feed Speed 133
- (Hexadecimal) 137
- Control Codes 139
- STX T Print Time and Date 140
- )s###W Font Descriptor 143
- *c###E Character Code 144
- Generating Label Formats 145
- Printhead Location 145
- Home Position 145
- Generating Records 146
- The Structure of a Record 146
- Record Structure Types 150
- Field Valid Inputs Meaning 150
- Width Multiplier 151
- Height Multiplier 151
- 4. Bar Codes 152
- Polygons 154
- Circles 155
- Advanced Format Attributes 157
- Appendix A 161
- 10K OHM 1/4 WATT 163
- ASCII text file 164
- Appendix B – Sample Programs 165
- Appendix C 173
- Appendix C – Available Fonts 174
- Appendix D 179
- Appendix D – Reset Codes 180
- Appendix E 181
- *Default Symbol Set 185
- Bar Code Summary Data 191
- Bar Code Details 195
- C: UPC-E 196
- E: Code 128 196
- Appendix G – Barcode Details 197
- F: EAN-13 198
- G: EAN-8 198
- I: Codabar 199
- K: Plessey 200
- Q: UCC/EAN Code 128 202
- T: Telepen 204
- byte count 206
- W1c: DataMatrix 209
- W1d / W1D: QR Code 213
- W1f / W1F: Aztec 217
- Barcode W1f 220
- Barcode W1F 220
- W1g / W1G: USD-8 (Code 11) 221
- <STX>L 224
- 34 567890 123 4567 229
- W1z: MicroPDF417 231
- Appendix H 235
- Appendix I 237
- Character Map Selection 239
- Appendix J 241
- I & W-Class GPIO 243
- See the WARNING 245
- • Pins 1 – 2 = +5VDC; 249
- • Pins 2 – 3 = +24VDC; or 249
- WARNING 251
- Signal Out 252
- Signal In 252
- Appendix K 253
- Module ID 256
- Appendix L 257
- Appendix M 259
- Commands by Function 260
- Function Command 260
- Table M-1: Commands (M-Z) 260
- Appendix N 261
- Command Description 263
- (continued) 263
- X X X X X X X 265
- Appendix O 267
- Figure O-2: Sample Label 268
- Appendix P 269
- Appendix Q 271
- ILPC-KANJI Option 272
- ILPC-CHINESE Option 275
- Appendix R 279
- Appendix S 281
- Appendix S – Line Mode 282
- Appendix T 285
- Label Formatting Mode 286
- Appendix T – RFID Details 287
- GEN2 Kill/Access Passwords 290
- GEN2 Lock States 290
- Appendix U 291
- Appendix V 295
- Glossary 297
Manuais e produtos relacionados com Impressoras Datamax-oneil Class Series Programmer’s Manual
Impressoras Datamax-oneil I-Class Mark II Wired_Wireless LAN Option Manual do Utilizador
(10 páginas)
(10 páginas)
Impressoras Datamax-oneil I-Class Mark II SDIO_USB Host Option Installation Manual do Utilizador
(6 páginas)
(6 páginas)
Impressoras Datamax-oneil PrintPAD AN-12 (Line Printer and Easy Print Modes) Manual do Utilizador
(2 páginas)
(2 páginas)
Electrolux ER8548B manuály
Uživatelské manuály a uživatelské příručky pro ne Electrolux ER8548B.
Poskytujeme 1 manuály pdf Electrolux ER8548B ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comentários a estes Manuais